filename: tfs 261b.doc version 1.1 19.05.2009 vectron international filter specification tfs 261b 1/5 vectron international gmbh & co. kg potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@v e ctro n.co m measurement condition ambient temperature: 23 c input pow er level: 0 dbm terminating impedance: * input: 720 ? || -5,7 pf output: 580 ? || -6,7 pf ch aracteristics remark: the reference lev e l for the relativ e attenuation a rel of the tfs 261b is the mini mum of the pass band attenuation a min . the minimum of the pass band attenuation a min is defined as the insertion loss a e . the centre frequency f c is the arithmetic mean v a lue of the upper and low e r frequencies at the 1,5 db filter attenuation lev e l relativ e to the insertion loss a e . the nominal frequency f n is fix ed at 261,0 mhz w i thout any tole rance. the giv en v a lues for both the relativ e attenuation a rel and the group delay ripple hav e to be achiev ed at the frequencies giv en below ev en if the centre frequency f c is shifted due to the temperature coefficient of frequency tc f in the operating temperature range and due to a production tolerance for the centre frequency f c . d a t a ty p. v a lue tolerance / limit insertion loss a e 6 , 8 d b m a x . 1 1 , 0 d b (reference level) nominal frequency f n - 2 6 1 , 0 m h z centre frequency f c 2 6 1 , 0 m h z - pass band p b - f n 150,0 khz pass band ripple - m a x . 1 , 0 d b pass band v a riation 0 , 7 5 d b m a x . 1 , 5 d b relativ e attenuation a rel f n ? f n 1 5 0 , 0 k h z 0 , 7 5 d b m a x . 1 , 5 d b f n - 2 6 0 , 0 m h z ? f n - 0 , 8 mhz 4 3 d b m i n . 4 0 d b f n + 0 , 8 m h z ? f n + 2 3 9 , 0 mhz 4 3 d b m i n . 4 0 d b group delay at f n @ 25 c 1,58 s max. 100 ns group delay ripple w i thin pb 1 0 5 n s m a x . 2 0 0 n s pulse response **** (drive pulse trapezoidal pulse 3.5 s w i dth, 10-90% rise & fall time = 2.0+/-0.25 s) m i n . 3 5 d b subsequent sidelobes, (after the main lobe) 3 8 d b m i n . 1 6 d b third echo, (third sidelobe after the main lobe) 5 8 d b m i n . 3 5 d b return loss w i thin f n 100khz - m i n . 1 5 d b input pow er lev e l * * - max . 2 0 d b m operable temperature range - - 40 c ... + 105 c operating temperature range otr - - 40 c ... + 85 c storage temperature range - - 62 c ... + 105 c frequency inv e rsion temperature 2 2 c - temperature coefficient of frequency t c f *** -0,04 ppm/k 2 - *) the terminating impedances depend on paras itics and q-v a lues of matching element s and the board used, and are to be understo od as reference v a lues only . should there be additional ques tions do not hesitate to ask for an applic ation note or contac t our design team. **) for short term operation only , cy cle ti me 1:1000; 15 dbm max fo r continuous operation ***) ? f(h z ) = t c f (ppm/k 2 ) x (t-t 0 ) 2 x f cat (mhz). ****) t he pulse response perform ance has been sim u lated using m easured dev ice s-param et ers and the final perform ance is an inhe rent feature of the design. ge ne ra te d: ch ecked / a p p r o v ed : vectron international gmbh & co. kg reserves the right to ma ke changes to the product(s) and/or information contained herein w i thout notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information.
filename: tfs 261b.doc version 1.1 19.05.2009 vectron international filter specification tfs 261b 2/5 vectron international gmbh & co. kg potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@v e ctro n.co m f ilter ch aracteristic 251 253 255 25 7 259 261 263 265 267 269 27 1 -6 0 -5 4 -4 8 -4 2 -3 6 -3 0 -2 4 -1 8 -1 2 -6 0 f r eq u e n cy i n m h z m a g n it u d e in d b in s e r t i o n lo s s : - 6 .7 4 d b 260. 6 260. 68 260. 76 260. 84 260. 9 2 261 261 . 08 26 1. 16 2 6 1. 24 261. 32 261. 4 -1 0 -9 -8 -7 -6 -5 -4 -3 -2 -1 0 f r e que nc y i n m h z m a g n it u d e in d b 260. 6 260. 68 260. 76 260. 84 260. 9 2 261 261 . 08 26 1. 16 2 6 1. 24 261. 32 261. 4 1. 55 1. 57 1. 59 1. 61 1. 63 1. 65 1. 67 1. 69 1. 71 1. 73 1. 75 f r e que nc y i n m h z d e la y in s cons truc tion a nd pin c onne c t ion (all dimensions in mm) 1 1, 7 m a x . 14 ,1 m a x . 8, 5 m a x . 2,2 1, 02 4x 1,9 0 5 = 7, 62 1 5 6 10 da t e c o d e tfs 261b x21 date code: y ear + w eek x 2009 a 2010 b 2011 ... 1 input 2 ground 3 ground 4 ground 5 output rf return 6 output 7 ground 8 ground 9 ground 10 input rf return 50 ? t est circu i t c1 l1 sa w l 2 c2 10 2, 3, 4, 7, 8, 9 5 6 1 vectron international gmbh & co. kg reserves the right to ma ke changes to the product(s) and/or information contained herein w i thout notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information.
filename: tfs 261b.doc version 1.1 19.05.2009 vectron international filter specification tfs 261b 3/5 vectron international gmbh & co. kg potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@v e ctro n.co m stability characteristics, reliability after the follow i ng tests the filter shall meet the w hole specification: 1. shock: 500g, 1 ms, half sine w a ve, 3 shocks each plane; din iec 68 t2 - 27 2. vibration: 10 hz to 500 hz, 0,35 mm or g respecti vely , 1 octave per min, 10 cy cles per plan, 3 plans; din iec 68 t2 - 6 3. change of temperature: -55 c to 125c / 30 min. each / 10 cy cles din iec 68 part 2 ? 14 test n 4. resistance to solder heat (reflow ): reflow possible: three times max.; for temperature conditions refer to the attac hed "air reflow temperature conditions" on page 4; 5. esd ansi/esd s20.20-1999 , class 1a for hbm this filter is rohs compliant (2002/95/eg, 2005/618/eg) packin g tape & reel: iec 286 ? 3, w i th exception of value for n and minimum bending radius; tape ty pe ii, embossed carrier tape w i th top cover tape on the upper side; max. pieces of filters per reel: 1500 reel of empty components at start: min. 300 mm reel of empty components at start including leader: min. 500 mm trailer: min. 300 mm g do w ct f e g d1 p2 p1 po bo ao p u l l o ff di r e c t io n pi n m a r k e r ty p da t e c o d e ko t tape (al l di mensi ons i n mm) w : 24,00 po : 4,00 do : 1,50 e : 1,75 f : 11,50 g(min) : 0,60 p2 : 2,00 p1 : 12,00 d1(min) : 1,50 a o : 8,80 bo : 14,60 ct : 21,5 a c n w 1 w 2 r eel (all d i men s io n s in mm) a : 330 w 1 : 24,4 w 2 (max ) : 30,4 n(min) : 60 c : 13,0 the minimum bending radius is 45 mm. vectron international gmbh & co. kg reserves the right to ma ke changes to the product(s) and/or information contained herein w i thout notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information.
filename: tfs 261b.doc version 1.1 19.05.2009 vectron international filter specification tfs 261b 4/5 vectron international gmbh & co. kg potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@v e ctro n.co m a i r re flow te mpe r a t ure c onditions conditions exposure average ramp-up rate (30c to 217c) less than 3c/second > 100c betw een 300 and 600 seconds > 150c betw een 240 and 500 seconds > 217c betw een 30 and 150 seconds peak temperature max. 260c time w i thin 5c of actual peak temperature betw een 10 and 30 seconds cool-dow n rate (peak to 50c) less than 6c/second time from 30c to peak temperature no greater than 300 seconds chip-mount air reflow profile temperature / c max. 260c 217c time / s max. 300 s 10 ... 30 s 30 ... 150 s vectron international gmbh & co. kg reserves the right to ma ke changes to the product(s) and/or information contained herein w i thout notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information.
filename: tfs 261b.doc version 1.1 19.05.2009 vectron international filter specification tfs 261b 5/5 vectron international gmbh & co. kg potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@v e ctro n.co m history version reason of changes name date 1.0 generation of development s p e c i f i c a t i o n s t r e h l 2 0 . 0 1 . 2 0 0 9 1.1 - add of terminating impedances, ty pica l values, filter characteristics and matching configuration pfeiffer 19.05.2009 - change of time domain parameters vectron international gmbh & co. kg reserves the right to ma ke changes to the product(s) and/or information contained herein w i thout notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information.
|
